iFlight Blitz F7 Pro Flight Controller 35X35mm 4-8S (MPU6000)

iFlightSKU: DA2285

Price:
Sale price£72.90

Tax included Shipping calculated at checkout

Stock:
In stock

Order before 3pm Mon-Fri and your order WILL be dispatched same-day.

Same-day dispatch excludes bank holidays and special circumstances - always consult our announcements bar at the top of the page for any exceptions.

Additional Information

Due to the permanent and potentially destructive nature of soldering and connecting to other devices in general, always remember to test electronics first, before attempting to solder to them or connect any accessories.

For a flight controller, this can always be achieved by connecting to the board via USB and verifying that everything is working via the configurator. To test an ESC, you can power up the board via crocodile clips. We sell crocodile clips here for this very purpose.

Please see the Items requiring soldering section of our refund policy for more information.

Reward Points ⭐️

You could earn 218 points from this item. Learn more.

Description

Featuring the very best technologies that iFlight has to offer, this amazing new flight controller from iFlight not only looks the part but offers some of the best performance on the market today. With an improved circuit design, all-around better components, and an even lower electrical noise floor, this Flight Controller should be your shopping list!

Features

  • Improved circuit design, better components, and lower electrical noise!
  • DJI HD VTX Connector (Plug-and-Play / No soldering required)
  • FC indicator LEDs for visual debugging
  • 512MB BlackBox
  • With LC filter

Specifications

  • Mount pattern: 35*35mm/ 4mm PCB hole diameter
  • Smartaudio / IRC Tramp VTX protocol supported
  • Firmware target: IFLIGHT_BLITZ_F7_PRO
  • Input Voltage: 14.8V-34V (4S-8S LIPO)
  • Motor outputs: 4x (SH1.25 connector)
  • Flash: 512MB (Blackbox flash)
  • I2C serial: SDA / SLA pads
  • Dimensions: 41*41.5mm
  • Barometer: DPS310
  • OSD Chip: AT7456E
  • LED controller: Yes
  • MCU: STM32 F722
  • Weight: 17g (±2)
  • Beeper pad: Yes
  • Gyro: MPU6000
  • UARTS: 6

Wiring suggestions

  • UART1 for VTX HD/Analog
  • UART2 for Receiver
  • UART4 for GPS
  • UART5 for ESC Telemetry
  • 8×Dshot/PWM outputs
  • 1×I2C for GPS Mag

Tips

1. F722 MCU has an inner inverter.
2. SBUS、CRSF、ELRS、IBUS、DSM ETC... can be connected to any unused UART_RX, we suggest you connect to Uart_RX2
3. Frsky SmartPort, Tramp & Smartaudio can be connected to any unused UART_TX, we suggest you connect to Uart_TX1
4. F.port can be connected to any unused UART_TX, we suggest you connect to Uart_TX2

Included Connectors (Plug-and-Play wire harness)

  • 1xGH1.25 7pin connector for HD VTX/Analog VTX(RX2/GND/RX1/TX1/GND/+12V/Video out)
  • 1xGH1.25 8pin connector for ESC1 (GND/VBAT/M1/M2/M3/M4/CUR/RX5)
  • 1xGH1.25 8pin connector for ESC2 (GND/VBAT/M5/M6/M7/M8/CUR/RX5)
  • 1xGH1.25 4pin connector for GPS&Mag(+5V/GND/TX4/RX4/SDA/SCL)
  • 1xGH1.25 3pin connector for Analog camera (Video in/GND/+5V)
  • 1xGH1.25 4pin connector for Any Receiver(GND/+5V/RX2/TX2)
  • 1xGH1.25 4pin connector for LED&Beeper(LED/BZ-/+5V/GND)

What's in the package?

  • 1 pc BLITZ F7 Pro Flight Controller
  • 1 set of FC connectors (as above)
  • 1 set silicone grommets

Product Details

Product TypeFlight Controller
Shipping Weight100 grams
VendoriFlight

Found it cheaper elsewhere?

Get in touch and we'll price match it for you 👌. Terms and conditions apply.

Customer Reviews

Did you know that you could earn 50 reward points for every product review left and an additional 25 points for also adding a photo? Learn more.

Support Information

Further product support information: https://iflightrc.freshdesk.com/support/home

You may also like

Recently viewed